Perfect Integration Monitor Station

Sign in to your dashboard

No account? Create one
Perfect Integration Monitor Station
Signed in as
/ searchEsc back
/

Details

Discovered

History

    Settings

    Advanced settings are shown. Wrong values here can stop the scanbox finding devices, or get its switch port blocked. The defaults suit most sites.

    Software update

    The scanbox updates itself on a 10-minute timer. Update now makes it update at its next check-in (about 15 seconds) instead.

    Scanbox web GUI

    The scanbox's own web interface, opened in its remote browser. Its certificate is self-signed, so the browser warns first: choose Advanced, then Proceed. It asks for the scanbox's own login.

    Background scan

    When

    Networks

    What it does

    Speed

    However fast it's set, the scanbox scans one device at a time and stays under its traffic limit (Scanning card, under Advanced), so switches don't mistake it for an attack.

    Limits

    Scanning

    Traffic limit

    Every scan on this scanbox (background scan, new-device checks, Scan now) shares this budget of new connections per second, evenly spaced with no bursts. 50 is the most it will ever send: low enough for switches' SYN-flood and DoS protection. If a switch still blocks the scanbox's port, lower it.

    Port checks

    VLANs

    Each VLAN the scanbox hears on its trunk gets its own interface, so it can reach and scan the devices there directly. Ignore removes that interface and stops reporting devices seen on it; Hide only leaves the VLAN off the scanbox page's VLAN tabs, its devices still listed under All VLANs; IP gives the interface a fixed address instead of DHCP. Changes reach the scanbox at its next check-in (about 15 seconds) and show as pending until it confirms. Which VLANs the background scan covers is set under Background scan → Networks.

    VLANName InterfaceAddressIgnoreHideIPState

    Unregister

    Factory resets the scanbox at its next check-in (about 15 seconds): its registration, VLANs and everything it has found are wiped; its network settings and local admin password are kept. It then disappears from the dashboard along with all its discovered hosts and their history. To use it again, register it again. Remove without reset is for a scanbox that is gone or broken and will never check in.

    Company accounts
    Who can sign in to your company's dashboard

    Create account

    New accounts have no password: generate a setup code for them, and they enter it under Create one on the sign-in page to choose their own. A code works once, for 72 hours.

    Accounts

    IDUsernameRoleStatus
    My profile
    Your password, two-factor authentication and devices

    Account

    Password

    Changing it signs you out on every other device.

    Two-factor authentication

    Devices

    The browsers you've signed in from, this one first. A trusted one skips the 2FA code. Block a browser you don't recognise: its sessions end now and it can't sign in until you unblock it. Then change your password.

    Recent security activity

    WhenWhatDeviceIP address
    Security log
    Sign-ins, 2FA, passwords, devices and account changes in your company
    /
    WhenUserCompanyEventDetails DeviceIP address

    Entries are kept for a year.

    Feedback
    Suggestions, ideas and problems from everyone using the monitor
    Logs

    Webservers

    ServerStatusVersionLast update

    Database servers

    ServerStatusVersionLast update

    Scanboxes

    /
    ScanboxStatusVersionLast updateFault codes

    Recovery reports

    Updates that failed and rolled back automatically
    WhenDeviceWhat happenedVersions

    AI device-type detection

    Fault codes are explained in webserver/README.md.

       

      
      
      
        
        
      
      
    
      
        
  
    
      
      
      
      
      
        
        
      
      
    
      
        
  
    
      
      
      
        
        
        
      
      
      
        
        
      
      
    
      
        
  
    
      
      
      
        
      
          
      First, confirm it's you: your password and a code from the authenticator app you use now.
      
          
          
        
      
        
      
          
        
            
      1. Open the authenticator app on your new phone.
        2. 
            
      2. Scan this QR code with it, or type in the key below it.
        3. 
            
      3. Enter the 6-digit code the app shows.
        4. 
          
      
          
      
          
          
          
      
        
      
        
      
      
      
        
        
      
      
    
      
        
  
    
      
      
      Turn off 2FA for 48 hours?
      
        
      For when your phone or authenticator app is gone. For the next 48 hours you sign in with your
          password alone, and only on the devices you trust now, like this one. Set up a new authenticator
          app before then: if you don't, signing in needs an enrolment code from your admin.
          You can do this once every 30 days.
      
        
        
      
      
      
        
        
      
      
    
      
        
  
    
      
      
      Rename device
      
        
        
      
      
      
        
        
      
      
    
      
        
  
    
      
      
      Open a TCP tunnel
      
        
      Opens a port on the server that leads, through the scanbox, to . Point desktop
          software (Crestron Toolbox, PuTTY, ...) at the address it gives you.
      
        
        
        
        
      
        
      
      
      
        
        
      
      
    
      
        
  
    
      
      
      Restart PoE
      
        
      Turns the power on  of  off, then on again. Whatever it
          powers restarts and is offline until it has booted.
      
        
        
        
        
        Uses the write community saved for this switch.
          
        
        
        
          
          
        
        
        
        The scanbox does it over SNMP, and won't touch the port it is itself connected through.
        
        
        
      
        
        
        
      
        
    
        
          
  
    
        
      
        Device login
        
        
        For . Sent once to the scanbox, which keeps it encrypted and signs in from its own
          address. Nobody can read the password back, here or on the scanbox's dashboard.
        
        
        
        
        
        
        
      
        
        
        
      
        
    
        
          
  
    
        
      
        
        
        
        
        Command 
        
        
        
        
        
          
          
          
          
          
          
          
          
          
          
          
          
          
          
          
          
          
        
        
        
        
        
          
        
          
      
          
        
        
        
        
      
          
    
          
            
  
    
          
      
          
        
          The browsers they've signed in from. Blocking one ends its sessions at once and keeps it out until
          it's unblocked. For a lost phone, use Reset 2FA instead.